DIY Shrink Plastic Charms Using Cookie Molds クッキーの型を使ったプラ板チャームを作ってみた(ほぼ100均) | MosoGourmet 妄想グルメ

We made a charm using almost entirely material from the 100 yen shop! We're not great at drawing so we colored into decals. We used cookie molds because the shape makes it easy to understand what it is even only with the frame. You can enjoy creating cheap DIY's thanks to 100 yen shops like Cando or Daiso. We live in blessed times!

We received a comment that said that MosoGourmet seem to only make food crafts, but recently we've been getting the itch to get into things such as sewing and other handicrafts!

*Recipe*
1. Cut the plastic molds from Cando into 5cm squares, write the direction of the plate, and do a test bake. It is convenient to know the characteristics of the board because it shrinks and warps differently depending on them.
2. Mark it with masking tape so that you can see the vertical and horizontal directions and the front and back of the mold.
3. Cut the mold. If you want to make several, make the design face the same direction. The mold should be neatly shrunk by now.
4. File the entire surface so that the back of the mold is curved, with a #400 file from Daiso.
5. When the entire unit becomes white, remove any debris with a wet tissue.
6). When the mold is dry, place a cookie mold on its surface and take out its shape with the file.
7. Color in with color pencils. This time, we used a watercolor pen. Watercolor pencils are sold in 12 colors at Cando and Daiso.
8. In the case of a watercolor pen, blur the color with a brush (from Daiso) containing a small amount of water (Daiso also sells paint plates). If you want to make it darker, add some color with the watercolor pen before it dries.
9. Cut a little inside the frame with scissors or a cutter. It's difficult to cut the fine parts, so we used eyebrow scissors.
10. Bake in a preheated toaster oven for about 2 minutes. Put it on the oven sheet (colored side up) and keep it in the oven toaster, keeping an eye on it while it shrinks. When it stops shrinking, take a breath and take it out the oven sheet.
11. Place it on a hard, flat surface that is resistant to heat and press it with a metal tray. Be careful, it's hot!
12. When it cools down, apply your favorite top coat. This time, we used a water-based topcoat spray (a matte "Mr.hobby"). When it dries up, spray it on the back side (the colored side) to prevent discoloration.
13. Attach your favorite accessories. This time, we drilled holes in it with a hand drill (from Cando) and a pin vice, and attached a crab that I bought at Daiso. Round-nosed pliers and finger holders can be purchased at a 100 yen shop.
14. All done. We'd like to make it again!

ほぼ100均アイテムでプラバン Shrink Plastic を使ったチャームを作りました。絵心が乏しいので着色は写し絵の色塗りだけ。形も枠だけで何かわかる工夫がされているので、クッキー型を使いました。100円ショップ(キャンドゥ、ダイソー)のおかげで安く手作りが楽しめる。いい時代だ。
妄想グルメは食品工作みたいだってコメントがあったけど、最近、本来の傾向の、お裁縫や工作などクラフト系やりたい虫が疼き出してるな。

(クッキングシート使用上の注意 https://www.lion.co.jp/ja/products/246 )

*レシピ*
1.プラバン(キャンドゥ)は5センチ四方に切り、板の方向を書き込んで試し焼きをする。板によって縦横の縮み方、反り方が異なるので、その板の性格を知っておくと便利です。
2.プラバンの縦横の方向と表裏がわかるようにマスキングテープなどで印を付ける。
3.プラバンを切る。いくつか作る場合はデザインの縦横を同じ方向にする。プラバンの縮み方が揃ってきれいに仕上がる。
4.プラバンの裏を400番のヤスリ(ダイソー)で回すように全面やすりをかける。
5.全体が白くなったらウエットティッシュなどでゴミを落とす。
6.プラバンが乾いたら、ヤスリをかけた面にクッキー型で枠の型を取る。
7.色鉛筆で着色する。今回、水彩色鉛筆を使いました。水彩色鉛筆はキャンドゥとダイソーで12色入りが売られていました。
8.水彩色鉛筆の場合は、少量の水(絵具皿はダイソー)を含ませた筆(ダイソー)で色をぼやかす。濃くしたいときは乾かないうちに水彩色鉛筆で書き足す。
9.ハサミやカッターを使って枠のほんの少し内側を切る。細かい部分は切りづらいので眉毛切バサミを使うとうまくできました。
10.2分ほど予熱したオーブントースターで焼く。オーブンシートにのせ(着色面が上)、オーブントースターに入れると数秒で縮んでくるので目を離さないこと。縮むのが止まったら一呼吸おいてオーブンシートごと取り出す。(クッキングシート使用上の注意 https://www.lion.co.jp/ja/products/246 )
11.熱に強い、固く平らな物の上に置き、金属のトレイなどでプレスする。熱いので気をつけて!
12.冷めたらお好みのトップコートをする。今回は水性トップコートスプレー(Mr.hobbyの つや消し)をしました。乾いたら裏面(色鉛筆の面)にもスプレーし色落ちを防ぐ。
13.好みのアクセサリーパーツを付ける。今回はハンドドリル(キャンドゥ)やピンバイスで穴を空け、ダイソーで買ったカニカンを付けました。ラジオペンチや指かん(ダイソー)も100円ショップで買うことができます。
14.でけた。また作りたい。

#DIY #Charms #ShrinkPlastic #craft #手作り #プラバン #工作
Share this Post:

Related Posts: